It somehow escaped our attention that we did not publish a bug/feature list for the beta. Here is a list of bug/features that were updated for version 12.0.0.4
OLI Studio Bugs
| Program | Bug | Version Fixed |
| All Programs | Report Table Editor for GREF for selected species does not work | 12.0.0.1 |
| All Programs | No kinetics editor in surveys | 12.0.0.1 |
| All Programs | Units, gauge pressure does not display if set to 0 | 12.0.0.1 |
| All Programs | Typographical errors in manuals corrected | 12.0.0.1 |
| All Programs | Interaction matrix does not include transport properties | 12.0.0.1 |
| All Programs | All sample case files updated | 12.0.04 |
| Scalechem | Case saved in previous version did not open in the beta | 12.0.0.2 |
| ScaleChem | Exporting a facilities calculation to a CSV file only used 22 nodes | 12.0.0.1 |
| Stream Analyzer | Case with custom surveys fails to load because custom surveys are not enabled | 12.0.0.1 |
| Stream Analyzer | Case with a mixer failed in 11.5 but worked in previous versions | 12.0.0.1 |
| Stream Analyzer | A case crashed when enabling kinetics | 12.0.0.1 |
| Stream Analyzer | A case crashed when clicking on the report tab with a badly formed private database | 12.0.0.1 |
| Stream Analyzer | Phase behavior in CCTUS was odd. | 12.0.0.1 |
| Stream Analyzer | Mass balance errors – improperly loaded database | 12.0.0.1 |
| Stream Analyzer | Program crash when copying data from one case to another. Bad units | 12.0.0.1 |
| Stream Analyzer | Scaling inhibition species are hard to visualize in the grid, the letter “I” was added | 12.0.0.1 |
OLI Flowsheet Bugs
| Program Area | Bug | Version Fixed |
| Unit Manager | Liquid-1 updated from Aqueous | 12.0.0.1 |
| Unit Manager | Expanded Cp units for heat exchanges | 12.0.0.1 |
| Unit Manager | Units in call out do not match unit manager | 12.0.0.1 |
| Report | Missing pre-scaling tendencies for some areas of the report | 12.0.0.1 |
| Report | When closing a case, the report tab locations are not saved | 12.0.0.1 |
| Report | Cannot adjust error panel window | 12.0.0.1 |
| Chemistry Builder | Dropdown box produced an error if selecting the same species | 12.0.0.1 |
| Chemistry Builder | Add classical inert species (found in Chemistry Wizard) | 12.0.0.1 |
| Chemistry Builder | Cannot identify private database names from the model builder | 12.0.0.1 |
| Chemistry Builder | Cannot edit Pseudocomponent parameters as can be done in OLI Studio. | 12.0.0.1 |
| Compressor | Isentropic compressor does not report constant enthalpy | 12.0.0.4 |
| Controller | A limit of 50 is too restrictive | 12.0.0.1 |
| Mixer | Inconsistent final adiabatic temperature when run single case or in sensitivity | 12.0.0.2 |
| Optimizer | Final value is negative, but report is positive | 12.0.0.1 |
| Reactor/Kinetics | Mass-balance errors in user spec equations | 12.0.0.1 |
| Reactor/Kinetics | Added new block, reactor-separator which combines both blocks | 12.0.0.1 |
| Reactor/Kinetics | Ion exchange reactions not supported | 12.0.0.1 |
| Reactor/Kinetics | A reverse rate is calculated when not is specified | 12.0.0.1 |
| Sensitivity | Multistage blocks not supported | 12.0.0.1 |
| Sensitivity | Range selection not honored | 12.0.0.1 |
| Sensitivity | Report of errors of species that are missing but are actually in the model | 12.0.0.1 |
| Sensitivity | Block parameters not included | 12.0.0.1 |
| Separator | Copied block fails in new case | 12.0.0.1 |
| Separator | Change entrainment tags from “Dissolved” to “Entrained” | 12.0.0.1 |
| Split | Cannot change the mass/mole type in the call-out | 12.0.0.1 |
| Run-time-Error | Case worked in version 11.5 but failed in Beta | 12.0.0.4 |